DC12V 1 Channel Wireless Remote Transmitter Receiver 433MHZ Learning Code

Description

Note: The color of the item may vary slightly due to photography and your own computer
The wireless RF remote controls are widely used for data transmitting and signal control and are widely used in remote control garage, roller curtain, entrance guard switch controller, industrial control and wireless security alarm industry.
Wireless Remote Transmitter : 2 Key Remote Control, 1 x 27A 12V Alkaline Battery Battery, SC2260 Chip, 433MHz.
Receiver Module: DC12V, 1 Channel.
Suitable for security alarm, remote control electric doors and windows, signal control, industrial control, the electric control, etc.
Specifications:
Product Name : Wireless Remote Transmitter Receiver;
Button Quanity : 2 Key Remote Control;
Relay Rated : AC 10A 125V/250VDC 10A 28V/30V
Channel Numbers :1CH;
Remote Control Distance: 15-30m
Operating Frequency : 433MHZ;
Powered By : 1 x 27A 12V Alkaline Battery(Not Included Here);
Relay Coil Voltage : DC12V
Coding Type : Learning Code
Transmitter Size : 60 x 26 x 14mm/2.4" x 1" x 0.55"(LxWxT);
Receiver Module Size :50x35x22cm/19.68x13.77x8.66Inch(LxWxT);
Materials : Plastic, Electronic Parts
Color : Black, Silver Tone;
Weight : 58g;
Operation Way and Steps:
1. Factory Default is Inter-locking Mode.
Press the button A, the Receiver A (Relay A) turns on; Press the button B, the Receiver B (Relay B) turns on, the Receiver A (Relay A) turns off.
2. Each transmitter and receiver have been finished linking and factory default mode(Inter-locking Mode) has been set up. When you receive them, you do not need to link again, you just need to connect the wiring according to our wiring diagram layout.
About three modes:
1)Inching Mode:
Press and hold the button A, the Receiver A (Relay A)turns on; Release the button A, the Receiver A (Relay A) turns off.
2)Self- lock Mode:
Press the button A, the Receiver A (Relay A) turns on; Press the button A again, the Receiver A (Relay A) turns off.
3)Interlocked Mode:
Press the button A, the Receiver A (Relay A) turns on; Press the button B, the Receiver B (Relay B) turns on, the Receiver A (Relay A) turns off.
If you want to change the factory default mode to other two working mode, below is the operation steps:
1. Clear:
Press and hold the learning button on the receiver board, the red light (Signal Light) will turn on and stay on for about 5 seconds, till the red light turns off, then release the learning button. It means clearing succeed, previous mode will not work after clearing successfully.
2. Choose the Working Mode:
Press and hold the learning button on the receiver, the red light will turn on and stay on for about 5 seconds, then turn off (Clearing Steps), do not release, still hold the learning button, and then the red light will begin to flash, it will flash once, then twice, and finally three times.
(1).After the light flashes ONCE, release the learning button, it becomes Inching Mode.
(2).After the light flashes TWICE, release the learning button, it becomes Self- lock Mode.
(3).After the light flashes THREE times, release the learning button, it becomes Interlocked Mode.
3. Link the remote control:
(After the Working Mode is chosen, you can start to link the remote control according to the mode you choose)
Press the learning button on the receiver until the red light turn on, and then release the learning button, the red light will stay on. Press the button on the transmitter you want to link, and the red light (Signal Light) on the receiver board will flash twice, at this time, it means that the transmitter and receiver finish linking. Then you can press the button on the transmitter, the related receiver will work as the mode you choose.
Note:
1.When the receive has Single channel, you can only learn one button, just learn and link the button which you want to control.